Brisbane and Gold Coast
Concrete hand sawing in Brisbane and Gold Coast.
Hand sawing uses a portable powered saw with a circular diamond blade to cut concrete where access and the required cut suit the tool. Sirius Concrete Cutters provides hand sawing in Brisbane and the Gold Coast. Send the cut dimensions, concrete thickness and site photos to discuss the method and request a quote.
The short answer
What is concrete hand sawing?
A portable saw brings a circular diamond blade to the cut.
The operator guides the saw along the marked line. The circular blade limits how deep it can reach and how it finishes at a corner. Concrete thickness, working room and the required finish help determine whether hand sawing or another cutting method suits the job.
- 01
Localised cuts
Describe the section of concrete to be cut and the finish needed at each end.
- 02
Access assessment
Show the approach to the work area and the room available for the operator and saw.
- 03
Renovation work
Send plans for proposed openings or slab alterations so the cutting method can be assessed.
How the method works
A diamond blade follows the planned cut.
A hand-held saw is portable, but the cut still needs suitable access, depth and site controls.
Planned result Detailed-cut discussion.
- 01
Define the cut
Mark the intended line on a plan or photo. Include dimensions, concrete thickness if known and any finish requirements.
- 02
Check what is in the concrete
Share service drawings, scan results and known reinforcement. Confirm any structural review needed before an opening or section is cut.
- 03
Plan the work area
Discuss working room, access, nearby occupants, water and power availability, and arrangements for dust and slurry.
- 04
Agree the finished scope
Confirm the cutting method, treatment of corners and who will support, remove and dispose of the cut section.
Project situations
When should you discuss hand sawing?
Start with the cut you need; the method can then be matched to the concrete and site.
- 01
Localised cuts
Describe the section of concrete to be cut and the finish needed at each end.
- 02
Access assessment
Show the approach to the work area and the room available for the operator and saw.
- 03
Renovation work
Send plans for proposed openings or slab alterations so the cutting method can be assessed.
Before the first conversation
Send photos that show the whole work area.
Include a close view of the cut line and a wider view of access. For an opening, show both faces where accessible.
- Cut length, width and concrete thickness if known
- Plans, known services and any structural requirements
- Working room, access route and nearby occupied areas
- Dust, water, slurry and cut-section removal arrangements
For a useful quote
Give Sirius a clear cutting brief.
Dimensions and site photos help establish which method suits the work.
- Location
- Suburb, work area and access.
- Work
- Intended cut and location.
- Conditions
- Nearby materials or interfaces.
- Timing
- Preferred timing and site coordination.
Common questions
Hand sawing questions.
Method choice, access, corners and the information needed for a quote.
01How deep can a hand saw cut concrete?
The depth depends on the saw, blade and access to the cut. Send the concrete thickness and required cut depth rather than choosing a method from a general depth figure. Sirius can discuss whether hand sawing, ring sawing or another method suits the work.
02Can hand sawing make a square corner?
A circular blade leaves a curved cutting profile through the concrete. Where a square corner or a limit on overcutting matters, show that requirement on the drawing. Another tool or an agreed finishing method may be needed.
03What access does a hand-sawing job need?
The operator needs working room and a suitable position to control the saw. Send photos of the cut location and approach, including walls, steps, fences or other obstructions. Portability alone does not establish that a restricted space is suitable.
04What should I discuss about dust and water?
Tell Sirius whether the area is indoors or occupied, and identify nearby equipment, drains and water-sensitive finishes. Dust controls and any water or slurry collection need to be planned for the site before cutting.
05What should I send for a hand-sawing quote?
Send the Brisbane or Gold Coast suburb, cut dimensions, concrete thickness if known, plans and access photos. Include known services, structural requirements, timing and any removal needed. Use the form below or call Scott on 0499 771 066.
Hand sawing quote
Send the proposed cut and access details.
Tell Sirius the Brisbane or Gold Coast suburb, cut dimensions, concrete thickness and access limits. Include available drawings, dimensions and known services and any removal needed in your project details.
You can also call Scott on 0499 771 066.
Fields marked * are required.